Skip to content

Tile a large film on a small printer

When a film is wider or longer than your printer's sheet, print it as overlapping tiles and tape them together along the seam marks. In Zorofilm tiling is automatic: the tiles share one halftone across the seam, overlap by 3.2 mm by default and carry seam ticks to line them up.

3 min lugemist · Uuendatud 2026-11-07 · Zorofilm

When does a film not fit?

A film is the art plus its margins and label strip; in Zorofilm that is 15 mm of margin on every side plus an 8 mm label strip. So a 304.8 mm (12 in) wide print needs a 334.8 mm wide film, more than the 330.2 mm (13 in) the ET-8550 takes. A4 printers such as the ET-8500 (215.9 mm) or the L8050 (216 mm) reach the limit with much smaller prints.

What are the options?

  • Rotate the art: a print that is too wide often fits along the sheet. Zorofilm says when rotating would make it fit.
  • Narrow the margins in the Films tab, as long as the marks still fit.
  • Use a bigger sheet: A4, Letter, A3, 11 × 17 in, A3+ / 13 × 19 in and 17 × 22 in are built in.
  • Tile it: print the film in parts and join them.
  • Send it out: export the films as PDF and have a wide-format printer print them.

How does Zorofilm tile?

  1. Films tab → Bigger than the sheet: Tile it (the default) or Warn only.
  2. Each film is split into tiles that overlap by the Tile overlap, 3.2 mm by default; change it to suit your tape and light table.
  3. The halftone runs across the seam, so the dots continue from one tile into the next instead of starting again.
  4. Seam ticks on both tiles mark where they meet: overlap them on the ticks on the light table and tape.
  5. The check strip says how many tiles each film needs before you print.

Does tiling use up more Free films?

No. On the Free plan every film counts once, also when it prints as several tiles or when several films share a sheet: a four-film job is four films whether it takes four sheets or twelve.

Can small films share a sheet?

Yes: Films → Several films on one sheet (cut apart) packs small films side by side with a gap between them (6.5 mm by default), so a left-chest job does not use a whole A3+ sheet per ink. Cut them apart before the screens are made.

What about long sheets and rolls?

Some printers take long sheets: Epson's ET-8550 accepts user-defined sizes up to 13 × 78.7 in through its rear straight path, one sheet at a time. Roll printers such as the 24 in SureColor T3170x avoid tiling for most prints, but Zorofilm cannot drive that model yet: export the films and print them with its own driver or RIP.

Allikad

  1. Epson US, ET-8550 specification sheet (PDF) · vaadatud 2026-11-01
  2. Epson US, ET-8500/8550 rear thick-media slot FAQ · vaadatud 2026-11-01

Jäid millegi muu taha? Küsi — Zorofilmi meeskond vastab igale küsimusele.

Esita küsimus

Uued siiditrüki juhendid otse sinu postkasti

Umbes üks e-kiri kuus: uued juhendid, lahendused probleemidele, mille kohta inimesed küsivad, ning Zorofilmi uudised.

Umbes üks e-kiri kuus uute siiditrüki juhendite ja Zorofilmi uudistega. Kõigepealt saadame sulle e-postiga kinnituslingi ja tellimusest saad loobuda igal ajal. Privaatsuspoliitika

Proovi oma kujundusega

Zorofilm teeb seda, mida need juhendid selgitavad: värvilahutus, aluskiht, trapping, raster ja kiled, prinditud sinu Epsonil või eksporditud. Free-paketiga saad 10 kilet kuus, otseprint kaasa arvatud.