Skip to content

Tile a large film on a small printer

When a film is wider or longer than your printer's sheet, print it as overlapping tiles and tape them together along the seam marks. In Zorofilm tiling is automatic: the tiles share one halftone across the seam, overlap by 3.2 mm by default and carry seam ticks to line them up.

3 분 분량 · 업데이트 2026-11-07 · Zorofilm

When does a film not fit?

A film is the art plus its margins and label strip; in Zorofilm that is 15 mm of margin on every side plus an 8 mm label strip. So a 304.8 mm (12 in) wide print needs a 334.8 mm wide film, more than the 330.2 mm (13 in) the ET-8550 takes. A4 printers such as the ET-8500 (215.9 mm) or the L8050 (216 mm) reach the limit with much smaller prints.

What are the options?

  • Rotate the art: a print that is too wide often fits along the sheet. Zorofilm says when rotating would make it fit.
  • Narrow the margins in the Films tab, as long as the marks still fit.
  • Use a bigger sheet: A4, Letter, A3, 11 × 17 in, A3+ / 13 × 19 in and 17 × 22 in are built in.
  • Tile it: print the film in parts and join them.
  • Send it out: export the films as PDF and have a wide-format printer print them.

How does Zorofilm tile?

  1. Films tab → Bigger than the sheet: Tile it (the default) or Warn only.
  2. Each film is split into tiles that overlap by the Tile overlap, 3.2 mm by default; change it to suit your tape and light table.
  3. The halftone runs across the seam, so the dots continue from one tile into the next instead of starting again.
  4. Seam ticks on both tiles mark where they meet: overlap them on the ticks on the light table and tape.
  5. The check strip says how many tiles each film needs before you print.

Does tiling use up more Free films?

No. On the Free plan every film counts once, also when it prints as several tiles or when several films share a sheet: a four-film job is four films whether it takes four sheets or twelve.

Can small films share a sheet?

Yes: Films → Several films on one sheet (cut apart) packs small films side by side with a gap between them (6.5 mm by default), so a left-chest job does not use a whole A3+ sheet per ink. Cut them apart before the screens are made.

What about long sheets and rolls?

Some printers take long sheets: Epson's ET-8550 accepts user-defined sizes up to 13 × 78.7 in through its rear straight path, one sheet at a time. Roll printers such as the 24 in SureColor T3170x avoid tiling for most prints, but Zorofilm cannot drive that model yet: export the films and print them with its own driver or RIP.

출처

  1. Epson US, ET-8550 specification sheet (PDF) · 확인 2026-11-01
  2. Epson US, ET-8500/8550 rear thick-media slot FAQ · 확인 2026-11-01

다른 문제로 막히셨나요? 물어보세요. Zorofilm 팀이 모든 질문에 답합니다.

질문하기

새 실크스크린 인쇄 가이드를 이메일로 받아 보세요

한 달에 이메일 한 통 정도: 새 가이드, 많이들 묻는 문제의 해결법, Zorofilm 소식을 보내 드려요.

새 실크스크린 인쇄 가이드와 Zorofilm 소식을 한 달에 이메일 한 통 정도 보내 드려요. 먼저 확인 링크를 이메일로 보내 드리며, 언제든지 구독을 해지할 수 있어요. 개인정보 처리방침

내 아트워크로 직접 해 보세요

Zorofilm은 이 가이드에서 설명하는 일을 해냅니다: 색분해, 언더베이스, 트래핑, 망점과 필름을 Epson으로 출력하거나 내보냅니다. Free 요금제로 매달 필름 10장, 직접 출력 포함.