Skip to content

Make films from a PSD with spot channels

Drop the PSD into Zorofilm: each spot channel becomes one film, in the file's order, with the channel's own name, and nothing is separated again. Save the PSD at 8 or 16 bits with Maximize compatibility on; Zorofilm uses the composite Photoshop saved, not the layers.

3 min lukuaika · Päivitetty 2026-11-07 · Zorofilm
Lyhyesti
  1. Save the PSD at 8 or 16 bits with Maximize compatibility
  2. Open it: Inks from shows The file's spot channels
  3. Rename channels or untick the ones you will not print
  4. Turn Zorofilm's underbase off if the file has its own base channel
  5. Set the halftone for the tints and check every film

Who sends PSDs with spot channels?

Separators. Photoshop plug-ins such as UltraSeps and T-Seps work in spot channels, and so do shops that separate by hand in Photoshop. The channels are the films: the separation work is done, and separating the picture again would undo it.

What does Zorofilm do with it?

  1. Every spot channel becomes an ink, named as in the file, in the file's order, with its display colour.
  2. Inks tab → Inks from: The file's spot channels. Rename a channel, or untick it to leave it off; its pixels stay exactly as separated.
  3. Black in a channel is full ink, as Photoshop shows it; grey is a tint, which is halftoned at the job's LPI, angle and dot.
  4. Choose Separate the artwork instead to ignore the channels and separate the composite image like any other artwork.
  5. A PSD without spot channels is separated from its composite as usual.

Which PSDs are read?

  • Colour modes RGB, CMYK, Grayscale and Multichannel, at 8 or 16 bits per channel.
  • Raw or PackBits image data, which is what Photoshop writes with Maximize compatibility on.
  • The file's resolution sets the print size. A PSD that does not state one is assumed to be 300 ppi; set the width in the Job tab.

What is not read?

  • Layers: the composite Photoshop saved is used, so save with Maximize compatibility after the last edit.
  • PSB (large document) files: save as PSD.
  • ZIP-compressed image data: save again with Maximize compatibility.
  • Bitmap, Indexed, Duotone and Lab modes, and 32-bit files: convert to RGB, CMYK, Grayscale or Multichannel at 8 or 16 bits.
  • Each of these gets a message that says what to do.

What should you check before printing?

  • The print width: the file's own size is used unless you change it.
  • The halftone for the tints, in the Halftone tab. Separators often publish theirs: UltraSeps' sheet gives 26° at 55 LPI with an elliptical dot for simulated process.
  • Every film with the loupe, in print order.

This path is new. Zorofilm reads spot channels the way Adobe's PSD specification describes them, and we confirm it on real shop files as they come in. If a channel comes out inverted or empty, tell us in the community or through support.

Lähteet

  1. Adobe, Photoshop File Formats Specification · haettu 2026-11-01
  2. S. Roginski, “Suggested Film Output Settings”, UltraSeps (PDF) · haettu 2026-11-01

Jumissa jonkin muun kanssa? Kysy – Zorofilm-tiimi vastaa jokaiseen kysymykseen.

Kysy kysymys

Uudet silkkipainon oppaat suoraan sähköpostiisi

Noin yksi sähköposti kuukaudessa: uusia oppaita, ratkaisuja ongelmiin, joista ihmiset kysyvät, ja Zorofilmin uutisia.

Noin yksi sähköposti kuukaudessa: uusia silkkipainon oppaita ja Zorofilmin uutisia. Lähetämme ensin sähköpostiisi vahvistuslinkin, ja voit perua tilauksen milloin tahansa. Tietosuojaseloste

Kokeile omalla kuvallasi

Zorofilm tekee sen, mitä nämä oppaat selittävät: erottelut, pohjavalkoisen, ylitäytön, rasterit ja filmit, tulostettuna Epsonillasi tai vietynä. Free-paketilla teet 10 filmiä kuukaudessa, suoratulostus mukana.