Skip to content

Trapping for screen printing: how much and which way

Trap by spreading the lighter ink slightly under its darker neighbour, so a small misregistration shows no gap, and never spread onto the garment. A practical size from Screen Printing magazine: print a test, measure the largest gap between the inks, and trap twice that.

3 min lukuaika · Päivitetty 2026-11-07 · Zorofilm
Lyhyesti
  1. Choose your press in Base & trap
  2. Or measure your press's largest gap and enter twice that
  3. Check the edges between inks with the loupe
  4. Measure again when frames, mesh or press change

Why trap at all?

Screens never register perfectly: frames flex, mesh stretches, platens shift. Where two inks only touch, any shift opens a thin line of garment between them. A trap makes them overlap a little, so a small shift stays hidden under the darker ink.

Which ink spreads?

The lighter one, under the darker one, so the darker edge keeps defining the shape; that is general prepress practice. A black keyline that overprints the colours under it hides registration the same way, and Fresener traps a black outline by fattening the black.

How much trap?

  • Fresener (T-Biz): 2–4 pixels at 300 dpi, about 0.17–0.34 mm, and more on loose presses.
  • Trimingham (Screen Printing, 2025): print a test, measure the largest misregistration gap and trap twice it. His example: a 1/64 in gap gets a 1/32 in trap; specialty items may need 1/16 in or more.
  • Heavy white through fine mesh, and underbase screens, stretch more (Trimingham).
  • Too much trap causes bleeding, loss of detail and colour shifts (Trimingham). Keep a small trap even on a press that registers well.

What does Zorofilm do?

Base & trap → Press sets the trap: Automatic press 0.1 mm, Manual, tight 0.2 mm, Loose / wooden frames 0.4 mm. These are our starting points drawn from the sources above, not measurements of your press, and the app marks them as estimates; type your own value once you have measured your gap. The lighter inks spread under the darkest one inside the artwork only, never onto the shirt. A one-ink job gets no trap.

How do you find your own gap?

This is Trimingham's method: print a two-colour test without trap, using films with marks, find the worst place between the two inks, and measure the gap there (a loupe with a scale helps). Enter twice that as the trap. Your press, frames and mesh decide the number, so measure again when one of them changes.

Lähteet

  1. S. Fresener, “Choking, Trapping & Cleaning up Type in Photoshop”, T-Biz Network, 2017 · haettu 2026-11-01
  2. T. Trimingham, “How to trap artwork for screen printing”, Screen Printing, 2025 · haettu 2026-11-01

Jumissa jonkin muun kanssa? Kysy – Zorofilm-tiimi vastaa jokaiseen kysymykseen.

Kysy kysymys

Uudet silkkipainon oppaat suoraan sähköpostiisi

Noin yksi sähköposti kuukaudessa: uusia oppaita, ratkaisuja ongelmiin, joista ihmiset kysyvät, ja Zorofilmin uutisia.

Noin yksi sähköposti kuukaudessa: uusia silkkipainon oppaita ja Zorofilmin uutisia. Lähetämme ensin sähköpostiisi vahvistuslinkin, ja voit perua tilauksen milloin tahansa. Tietosuojaseloste

Kokeile omalla kuvallasi

Zorofilm tekee sen, mitä nämä oppaat selittävät: erottelut, pohjavalkoisen, ylitäytön, rasterit ja filmit, tulostettuna Epsonillasi tai vietynä. Free-paketilla teet 10 filmiä kuukaudessa, suoratulostus mukana.