Skip to content

White underbase and choke for dark garments

On a dark garment, print a white underbase first so the colours on top stay bright, and choke it (shrink it) slightly so it never peeks out around them. Fresener's published range is 2–4 pixels at 300 dpi, about 0.17–0.34 mm; Zorofilm starts at 0.15 mm and lets you change it.

3 分鐘閱讀 · 更新於 2026-11-07 · Zorofilm
重點摘要
  1. Set the garment colour: anything but white turns the underbase on
  2. Set the choke: about 0.15 mm on a tight press, more on a loose one
  3. Leave highlight white on to print the art's white last
  4. Read the thin-detail warning
  5. Check the underbase film with the loupe

Why does a dark shirt need an underbase?

Most garment inks are not fully opaque: on black or navy cotton a light colour takes on the shirt's colour. A white layer under the colours gives them a light ground to sit on, so they print bright.

How much should you choke it?

  • Fresener (T-Biz): work at 300 dpi and choke 2–4 pixels, about 0.17–0.34 mm. Two pixels should be enough with close registration; more than four with wooden frames and a loose press.
  • A 1 pt stroke centred on the edge chokes only half its width: 0.5 pt, about 0.18 mm.
  • Too little choke and the white shows as a halo around the colours; too much and thin lines and small text lose their base and print dull.

Zorofilm sets the choke in millimetres, 0.15 mm by default, so it keeps its size whatever the artwork's resolution.

What is highlight white?

A second white printed last, in the brightest parts of the design, with black usually next to last (Fresener). UltraSeps gives 200–230 mesh for it. In Zorofilm, on a dark garment the white in the artwork becomes Highlight White and prints after the colours; the switch for it is in Base & trap.

Which mesh for the base?

  • UltraSeps: base on 156–230 mesh, highlight white on 200–230.
  • T-Biz (simulated process): base and highlight on 180–230.
  • ScreenPrinting.com: base on 110–156, top colours on 156–230, and 110 mesh for white.
  • Murakami: a white base on 250–300 mesh “simply won't print well”.

How does Zorofilm build the underbase?

  1. A garment colour other than white turns the base on (Automatic). You can force it on or off in Base & trap.
  2. The base is the union of every ink you print, so it sits under all of them; an ink you untick leaves the base too.
  3. Colours in the art that match the garment get no ink and no base, so the shirt shows through.
  4. The base is choked by the amount you set. When the art has fades, the base follows the fade instead of printing solid.
  5. It prints first: its film is the Underbase, number 1 in the print order.

Two checks watch it: an underbase on a white garment, which is usually not needed, and a choke that removes a noticeable share of the base, which means thin lines will print without it. A white-only design on a dark shirt becomes one white film instead of a base plus a white: print, flash and print again through the same screen, as shops on TheShirtBoard describe it.

來源

  1. S. Fresener, “Choking, Trapping & Cleaning up Type in Photoshop”, T-Biz Network, 2017 · 取得於 2026-11-01
  2. S. Fresener, “Simulated Process Color Separations – Part Two”, T-Biz Network, 2018 · 取得於 2026-11-01
  3. S. Roginski, “Suggested Film Output Settings”, UltraSeps (PDF) · 取得於 2026-11-01
  4. ScreenPrinting.com help centre, “How do I pick the right mesh count for my design?” · 取得於 2026-11-04
  5. Murakami Screen, “How to prevent moiré” · 取得於 2026-11-01
  6. TheShirtBoard, “Left chest print on black hoodie”, 2023 · 取得於 2026-11-04

還有其他地方卡關嗎?歡迎發問 — Zorofilm 團隊會回答每一個問題。

發問

新的網版印刷教學,直接寄到您的信箱

大約每月一封電子郵件:新的教學、大家常問問題的解決方法,以及 Zorofilm 的最新消息。

大約每月一封電子郵件,內容包括新的網版印刷教學與 Zorofilm 最新消息。我們會先寄送確認連結到您的信箱,您也可以隨時取消訂閱。 隱私權政策

用您自己的圖稿試試看

Zorofilm 做的正是這些教學所說明的:分色、白底、補漏白、網點與底片,用您的 Epson 列印或匯出。Free 方案每月 10 張底片,含直接列印。