Skip to content

White underbase and choke for dark garments

On a dark garment, print a white underbase first so the colours on top stay bright, and choke it (shrink it) slightly so it never peeks out around them. Fresener's published range is 2–4 pixels at 300 dpi, about 0.17–0.34 mm; Zorofilm starts at 0.15 mm and lets you change it.

3 นาทีในการอ่าน · อัปเดต 2026-11-07 · Zorofilm
สรุปสั้น ๆ
  1. Set the garment colour: anything but white turns the underbase on
  2. Set the choke: about 0.15 mm on a tight press, more on a loose one
  3. Leave highlight white on to print the art's white last
  4. Read the thin-detail warning
  5. Check the underbase film with the loupe

Why does a dark shirt need an underbase?

Most garment inks are not fully opaque: on black or navy cotton a light colour takes on the shirt's colour. A white layer under the colours gives them a light ground to sit on, so they print bright.

How much should you choke it?

  • Fresener (T-Biz): work at 300 dpi and choke 2–4 pixels, about 0.17–0.34 mm. Two pixels should be enough with close registration; more than four with wooden frames and a loose press.
  • A 1 pt stroke centred on the edge chokes only half its width: 0.5 pt, about 0.18 mm.
  • Too little choke and the white shows as a halo around the colours; too much and thin lines and small text lose their base and print dull.

Zorofilm sets the choke in millimetres, 0.15 mm by default, so it keeps its size whatever the artwork's resolution.

What is highlight white?

A second white printed last, in the brightest parts of the design, with black usually next to last (Fresener). UltraSeps gives 200–230 mesh for it. In Zorofilm, on a dark garment the white in the artwork becomes Highlight White and prints after the colours; the switch for it is in Base & trap.

Which mesh for the base?

  • UltraSeps: base on 156–230 mesh, highlight white on 200–230.
  • T-Biz (simulated process): base and highlight on 180–230.
  • ScreenPrinting.com: base on 110–156, top colours on 156–230, and 110 mesh for white.
  • Murakami: a white base on 250–300 mesh “simply won't print well”.

How does Zorofilm build the underbase?

  1. A garment colour other than white turns the base on (Automatic). You can force it on or off in Base & trap.
  2. The base is the union of every ink you print, so it sits under all of them; an ink you untick leaves the base too.
  3. Colours in the art that match the garment get no ink and no base, so the shirt shows through.
  4. The base is choked by the amount you set. When the art has fades, the base follows the fade instead of printing solid.
  5. It prints first: its film is the Underbase, number 1 in the print order.

Two checks watch it: an underbase on a white garment, which is usually not needed, and a choke that removes a noticeable share of the base, which means thin lines will print without it. A white-only design on a dark shirt becomes one white film instead of a base plus a white: print, flash and print again through the same screen, as shops on TheShirtBoard describe it.

แหล่งที่มา

  1. S. Fresener, “Choking, Trapping & Cleaning up Type in Photoshop”, T-Biz Network, 2017 · ดึงข้อมูลเมื่อ 2026-11-01
  2. S. Fresener, “Simulated Process Color Separations – Part Two”, T-Biz Network, 2018 · ดึงข้อมูลเมื่อ 2026-11-01
  3. S. Roginski, “Suggested Film Output Settings”, UltraSeps (PDF) · ดึงข้อมูลเมื่อ 2026-11-01
  4. ScreenPrinting.com help centre, “How do I pick the right mesh count for my design?” · ดึงข้อมูลเมื่อ 2026-11-04
  5. Murakami Screen, “How to prevent moiré” · ดึงข้อมูลเมื่อ 2026-11-01
  6. TheShirtBoard, “Left chest print on black hoodie”, 2023 · ดึงข้อมูลเมื่อ 2026-11-04

ติดเรื่องอื่นอยู่? ถามได้เลย — ทีม Zorofilm ตอบทุกคำถาม

ตั้งคำถาม

คู่มืองานสกรีนใหม่ ส่งตรงถึงอีเมลของคุณ

ประมาณเดือนละหนึ่งอีเมล: คู่มือใหม่ วิธีแก้ปัญหาที่หลายคนถามกันบ่อย และข่าวสารจาก Zorofilm

ประมาณเดือนละหนึ่งอีเมล พร้อมคู่มืองานสกรีนใหม่ และข่าวสารจาก Zorofilm เราจะส่งลิงก์ยืนยันไปทางอีเมลก่อน และคุณยกเลิกการรับข่าวสารได้ทุกเมื่อ นโยบายความเป็นส่วนตัว

ลองกับอาร์ตเวิร์กของคุณเอง

Zorofilm ทำสิ่งที่คู่มือเหล่านี้อธิบาย: การแยกสี underbase, trap, ฮาล์ฟโทน และฟิล์ม พิมพ์บน Epson ของคุณหรือส่งออก แพ็กเกจ Free ทำได้ 10 ฟิล์มต่อเดือน รวมการพิมพ์ตรง