There is no single best film printer: it depends on the film size you need and the ink route you accept. On published sources, the ET-8550 is the most-named A3+ model, the SureColor T3170x the main 24-inch one, and the SC-P700/P900 the route without a conversion. Check which RIP supports your model and its known issues before you buy.
This post is built from our printer dataset: 25 Epson models, each with its channels, its published all-black conversion routes, which film RIPs list it and its known issues, read from Epson's, the RIP makers' and the ink sellers' own pages on 2026-11-01. We do not rank them. We show what each route involves and where each model is in Zorofilm today.
Three ways to get black film from an inkjet
- All channels black (ABI). Every tank or cartridge is filled with black dye ink, so all nozzles print the film. Published routes include Lawson's SP-1319 package for the ET-8550 (six 70 mL all-black bottles, $1,999), InkOwl's guide and bottles, and Freehand's refillable kit for the Artisan 1430 ($229).
- One channel black. Only one slot gets the film ink and prints alone. Freehand's Select Tank mode does this, and it advises Dmax ink in the ET-8550's photo-black slot only while the warranty runs (AccuRIP tables).
- Stock ink, no conversion. Lawson sells the SureColor P700 and P900 as film printers on Epson's own pigment black (P900 at $1,295), and Epson sold screen-print editions of the P800 and T3270 whose black ink is certified "up to a 4.0 Dmax" (epson.com).
A fourth, less common route puts black in two tanks: CPL Fabbrika fills the black and yellow tanks of its ET-14000/14100 systems, saying four overlapping colours lay down too much ink to dry (cplfabbrika.com).
The models, side by side
| Model | Widest film | Published ink route | AccuRIP Emerald | Zorofilm today |
|---|---|---|---|---|
| ET-8550 (EU: L8180) | 13 in (A3+) | All tanks black (Lawson, InkOwl) or photo-black slot only (Freehand) | Select Tank, not All Black Ink | Beta, until our all-black hardware test |
| ET-8500 (L8160) | 8.5 in (A4/Legal) | All tanks black (InkOwl, Absolute Black) or photo-black slot | Select Tank | Beta |
| Artisan 1430 / Stylus Photo 1400 | 13 in (A3+) | Refillable all-black cartridges (Freehand, Ryonet, Lawson) | All Black Ink and Select Tank | Beta; discontinued by Epson |
| XP-15000 | 13 in (A3+) | Third-party all-black cartridges that need chipless firmware (seller's claim) | Select Tank | Experimental; black-only is the safe mode |
| L18050 / L8050 | A3+ / A4 | All tanks black (InkOwl compatible list) | Not listed | Experimental |
| SC-P700 / SC-P900 | 13 in / 17 in | Stock pigment black, no conversion (Lawson, Freehand) | Select Tank (P900 roll: All Black Ink on Windows) | Experimental: needs a black-channels-only kit |
| SC-T3170x (EU: SC-T3100X) | 24 in roll | All tanks black (ScreenPrinting.com package, InkOwl) or BK tank only on Mac | All Black Ink and Select Tank | Soon: needs new printer work |
| ET-15000 (L14150) | 13 in (rear feed) | All tanks black (Lawson package, now discontinued) or black only | All Black Ink and Select Tank | Soon |
| SC-P400, P600, P800 | 13 in / 13 in / 17 in | P400 and P600: refillable carts (InkOwl); P800 Screen Print Edition on stock ink | P400 and P800 listed; P600 not | Soon; discontinued by Epson |
| SC-T3270 | 24 in roll | Refillable carts (InkOwl); T3270 Screen Print Edition | All Black Ink and Select Tank | Soon; discontinued by Epson |
| ET-14100 / ET-2850 | A3 / A4 | Black and yellow tanks (CPL Fabbrika) | Not listed | Soon |
PrintFab's silkscreen list includes the L1800, L8050/L18050, ET-8500/8550, the SC-P400 to P900 line and the SC-T31xx to T72xx line (turboprint.info). Fiery FilmMaker 11 has no entry for the XP-15000, L8180, L805/L800 or L18050 (fiery.com).
Own an L805, L800 or L1800? Zorofilm has profiles for them (beta), but our data on their all-black conversion routes is not complete yet, so they have no printer page for now.
Known issues, as published
- ET-15000: its media sensor struggles to detect clear film. Freehand's compatibility tables footnote it, PrintFab lists it among printers with film-feed trouble, and a 2024 forum thread on TheShirtBoard did not resolve it (thread). Suggested workarounds were a paper carrier or a strip of low-tack tape.
- ET-14100 and ET-2850: also on PrintFab's list of printers with trouble feeding transparent film (turboprint.info).
- SC-P700 and P900 on stock pigment ink: Freehand says pigment is less dense than dye, can scratch off and struggles under strong LED units (Freehand help). We found no Epson statement that their black blocks UV; that claim is Lawson's.
- XP-15000: the all-black cartridge seller says Epson pushes updates that block third-party cartridges and that chipless firmware is needed (inkjetmall.com). Zorofilm never touches printer firmware or chips, so on this model the safe mode is black in one channel.
- Artisan 1430: end of life in 2017, per Freehand, which also describes split-head banding from partial clogs (Freehand help).
- ET-8550: Epson lists 360 nozzles for black and 180 per colour (epson.eu). The black channel's real nozzle layout is one of the things our hardware test still has to check.
About density figures
Ink and film makers publish Dmax numbers, for example Epson's "up to a 4.0 Dmax" for its screen-print editions. They are the makers' claims and are not measured the same way: some are UV readings, some visual, some do not say. Wasatch, a RIP maker, notes that the same roll read from under 2.0 to over 4.5 depending on the driver mode (wasatch.com). What matters is the density your printer, ink and film give together: Zorofilm prints a density ladder and a step wedge for you to measure with the procedure your film and emulsion makers publish.
Where Zorofilm stands
No model is marked "supported" yet: our own definition needs an all-black density and registration test on real hardware first, and that has not happened. Beta means a profile exists and shops demonstrably use the model for film; experimental means the profile is a nearest-model basis or the ink route differs; soon means new printer work is needed. On any printer, Zorofilm's per-ink PDF and PNG export works with your own driver or RIP. Free is 10 films a month, printing included.
Check your model on the printers page, then print the test films on it.
Download freeSources
Dataset: data/film-printers.json, retrieved 2026-11-01. Main sources, each read on 2026-11-01:
- AccuRIP Emerald compatibility tables: solutionsforscreenprinters.com/compatibility
- PrintFab silkscreen guide and printer list: turboprint.info
- Fiery FilmMaker v11 supported printers: fiery.com
- InkOwl all-black conversion guide: inkowl.com
- Lawson SP-1319 package: lawsonsp.com; Lawson P900 film printer: lawsonsp.com
- ScreenPrinting.com T3170x package: screenprinting.com
- Freehand All Black Ink kit: solutionsforscreenprinters.com; help articles: P700/P900, Artisan 1430
- Epson: ET-8550 (EU), SureColor P800 Screen Print Edition
- InkjetMall XP-15000 all-black ink: inkjetmall.com
- CPL Fabbrika ET-14000: cplfabbrika.com
- TheShirtBoard ET-15000 thread: theshirtboard.com
- Wasatch on film density: wasatch.com
- Kolormatrix film output service (if you would rather not own a film printer): kolormatrix.com, checked 2026-11-01
Frequently asked questions
Which printer do most screen printers use for film positives?
No sales figures are public. By how often it is named, the ET-8550 leads: it is in AccuRIP's top four, in Lawson's SP-1319 package and on InkOwl's bottle list. In 24 inches, the SureColor T3170x is the model the film packages use.
Can I make film positives without converting my printer?
Yes, on printers whose stock black is dense enough: Lawson sells the SC-P700 and P900 as film printers on Epson's pigment black. Freehand notes pigment is less dense than dye and can scratch off. Whether it is enough for your emulsion is decided by your own test film.
Is my printer supported by Zorofilm?
Each model has a page with its status (beta, experimental or soon). No model is marked supported until it passes our own all-black hardware test. See printers.
Do I need a 24-inch printer?
Only if you need films wider than your printer takes in one piece: A3+ models take 13 in. Zorofilm can also tile a bigger film across sheets, with an overlap you tape along the seam ticks.
