- Open Help and choose the printer and resolution
- Save or print the density ladder and the step wedge
- Read every column and patch
- Set Output → Ink density
- Test again for every new film, ink or print mode
Why test density at all?
Too little black and light gets through where the film should block it; too much and the ink pools, dries slowly or spreads, which fattens the dots. The right amount depends on the printer, ink, film and print mode, and vendors' density claims are not comparable (see choosing inkjet film). Wasatch notes that higher density on inkjet film usually brings more dot gain, so more ink is not automatically better.
What are the two test films?
- Density ladder: nine solid columns, 18 mm wide and 60 mm tall, each with more ink than the last and its value printed under it. With black in every channel the values run from 0.4 to 2.0 (1 = one channel at full coverage, shared across the channels); with black in one channel, from 0.2 to 1.0.
- Step wedge: patches of 2, 5, 10, 20, 30, 40, 50, 60, 70, 80, 90, 95, 98 and 100 % of one black ink, halftoned at 55 LPI and 22.5°, at the ladder's middle value.
- Each comes as a printer file, a 1-bit PNG and an exact-size PDF, with a README saying what each column is.
How do you make them?
- Open Help (the ? in the top bar) → Before the first real job.
- Choose the printer model and the resolution you print films at.
- Save the test films… writes the files to a folder; nothing is sent to the printer.
- Or choose where to send it in Output → Send to, press Print the density ladder or Print the step wedge, load one film sheet and confirm.
How do you read them?
- With a transmission densitometer: read every ladder column and the clear film. X-Rite's 361T, for example, has both UV and ortho responses, and Wasatch calls a transmissive UV densitometer ideal.
- Without one: the film, ink and emulsion makers publish their own test tools and procedures, such as Ulano's and KIWO's ExpoCheck, the Stouffer 21-step scale, Saati's 21 Step Guide and Murakami's step test instructions. Follow their instructions; Zorofilm gives no exposure advice.
- On the ladder, look for the column where the black stops getting denser and the ink starts to pool or spread. On the wedge, look at which small dots and which shadow holes survive on the film.
How do you use the result?
- Output → Ink density: set the value you chose.
- Write it down with the printer, ink, film and resolution. A change to any of the four is a new test.
- Print one real job and measure the 50 mm ruler and a solid area before a big run.
What this guide does not cover
Exposure times, emulsion and screen making. They depend on your exposure unit, emulsion and mesh, and only their makers can tell you. Zorofilm links to their published procedures and never promises a usable screen.
出典
- Wasatch SoftRIP help, colour separation linearity · 取得 2026-11-01
- X-Rite 361T brochure (PDF) · 取得 2026-11-01
- Ulano, ExpoCheck exposure calculator · 取得 2026-11-01
- KIWO, ExpoCheck · 取得 2026-11-01
- Ulano, exposure (Stouffer 21-step scale) · 取得 2026-11-01
- Saati, screen printing QC devices · 取得 2026-11-01
- Murakami Screen, Step Test Instructions · 取得 2026-11-01
ほかに困っていることはありますか?質問してください。Zorofilmチームがすべての質問に回答します。
質問する新しいスクリーン印刷ガイドをメールでお届け
月1通ほどのメールで、新しいガイド、よく寄せられるトラブルの解決策、Zorofilmのお知らせをお届けします。
