What causes moiré on a screen?
Two regular patterns on top of each other make a third, coarser one. A screen has two sources: ink against ink, when halftones of different inks print at angles that beat; and halftone against mesh, because the threads run at 0° and 90° and the knuckles where they cross form a 45° pattern. Rows of dots at 0°, 45° or 90° beat with the mesh.
Which angle should you use?
- 22.5° or 67.5°, half-way between the threads and the knuckles, is the usual answer; printers on TheShirtBoard report 25° or 61–67° working better on their own screens.
- Fresener (T-Biz) recommends 20–25° for basic halftones and calls 45°, the offset default, wrong for screen printing.
- UltraSeps uses 22.5° for CMYK and 26° for everything else.
- For CMYK, keep the inks 30° apart: Fresener gives 15 / 45 / 75 or 22.5 / 52.5 / 82.5, or one 22.5° or 25° angle for all process colours.
Why one angle for all spot inks?
Opaque inks printed wet on wet at different angles can form rosettes and ink-to-ink moiré. At one angle the mesh question is solved once, and dots of different inks sit side by side. The published settings from UltraSeps and T-Biz, and the Separation Studio manual as quoted on TheShirtBoard, all use one angle per job.
Why can no software predict it exactly?
The mesh is rarely square to the frame and its count changes with tension: a 305 mesh at tension may be about 290 threads per inch, the weft varies by 5–7 %, and a rotated screen changes the frequency (Screen Printing magazine, 2003). Murakami says plainly that “not all angles work”. The honest answer, as one printer on TheShirtBoard puts it, is the angle and dot that work on your screens.
How do you test it?
- Print one design with a large flat tint and a gradient at your usual LPI and angle.
- Print the same at a second angle, for example 22.5° and 25°.
- Print both on the same mesh and compare them on the garment, not on the film: moiré comes from the mesh, so the film alone will not show it.
- Keep the angle that looks clean for that mesh and LPI, and write it down per mesh.
What does Zorofilm do?
- Every job starts at 22.5°; change it in the Halftone tab.
- An angle within 5° of 0°, 45°, 90° or 135° gets a red warning: it runs along the mesh.
- An LPI too fine for the mesh gets its own warning; see LPI for mesh count.
- The loupe shows the real dots of each film at film resolution.
Kilder
- S. Fresener, “All About DPI, LPI, PPI & More”, T-Biz Network, 2015 · hentet 2026-11-01
- S. Roginski, “Suggested Film Output Settings”, UltraSeps (PDF) · hentet 2026-11-01
- S. Fresener, “Simulated Process Color Separations – Part Two”, T-Biz Network, 2018 · hentet 2026-11-01
- TheShirtBoard, “Sim. angles and dpi”, 2014 · hentet 2026-11-01
- Screen Printing magazine, “All Things Are Not as They Appear”, 2003 · hentet 2026-11-01
- Murakami Screen, “How to prevent moiré” · hentet 2026-11-01
Står du fast med noe annet? Spør – Zorofilm-teamet svarer på hvert spørsmål.
Still et spørsmålNye silketrykkguider i innboksen din
Omtrent én e-post i måneden: nye guider, løsninger på problemene folk spør om, og nytt fra Zorofilm.
