Skip to content

How to avoid moiré: screen angles for screen printing

Keep the halftone angle away from the mesh threads (0° and 90°) and the 45° pattern of their crossings: 22.5° or 67.5° are the usual choices, and many shops print every spot ink at one angle, such as 22.5° or 25°. No angle is safe on every mesh, so test on your own screens.

3 min. skaitymo · Atnaujinta 2026-11-07 · Zorofilm

What causes moiré on a screen?

Two regular patterns on top of each other make a third, coarser one. A screen has two sources: ink against ink, when halftones of different inks print at angles that beat; and halftone against mesh, because the threads run at 0° and 90° and the knuckles where they cross form a 45° pattern. Rows of dots at 0°, 45° or 90° beat with the mesh.

Which angle should you use?

  • 22.5° or 67.5°, half-way between the threads and the knuckles, is the usual answer; printers on TheShirtBoard report 25° or 61–67° working better on their own screens.
  • Fresener (T-Biz) recommends 20–25° for basic halftones and calls 45°, the offset default, wrong for screen printing.
  • UltraSeps uses 22.5° for CMYK and 26° for everything else.
  • For CMYK, keep the inks 30° apart: Fresener gives 15 / 45 / 75 or 22.5 / 52.5 / 82.5, or one 22.5° or 25° angle for all process colours.

Why one angle for all spot inks?

Opaque inks printed wet on wet at different angles can form rosettes and ink-to-ink moiré. At one angle the mesh question is solved once, and dots of different inks sit side by side. The published settings from UltraSeps and T-Biz, and the Separation Studio manual as quoted on TheShirtBoard, all use one angle per job.

Why can no software predict it exactly?

The mesh is rarely square to the frame and its count changes with tension: a 305 mesh at tension may be about 290 threads per inch, the weft varies by 5–7 %, and a rotated screen changes the frequency (Screen Printing magazine, 2003). Murakami says plainly that “not all angles work”. The honest answer, as one printer on TheShirtBoard puts it, is the angle and dot that work on your screens.

How do you test it?

  1. Print one design with a large flat tint and a gradient at your usual LPI and angle.
  2. Print the same at a second angle, for example 22.5° and 25°.
  3. Print both on the same mesh and compare them on the garment, not on the film: moiré comes from the mesh, so the film alone will not show it.
  4. Keep the angle that looks clean for that mesh and LPI, and write it down per mesh.

What does Zorofilm do?

  • Every job starts at 22.5°; change it in the Halftone tab.
  • An angle within 5° of 0°, 45°, 90° or 135° gets a red warning: it runs along the mesh.
  • An LPI too fine for the mesh gets its own warning; see LPI for mesh count.
  • The loupe shows the real dots of each film at film resolution.

Šaltiniai

  1. S. Fresener, “All About DPI, LPI, PPI & More”, T-Biz Network, 2015 · žiūrėta 2026-11-01
  2. S. Roginski, “Suggested Film Output Settings”, UltraSeps (PDF) · žiūrėta 2026-11-01
  3. S. Fresener, “Simulated Process Color Separations – Part Two”, T-Biz Network, 2018 · žiūrėta 2026-11-01
  4. TheShirtBoard, “Sim. angles and dpi”, 2014 · žiūrėta 2026-11-01
  5. Screen Printing magazine, “All Things Are Not as They Appear”, 2003 · žiūrėta 2026-11-01
  6. Murakami Screen, “How to prevent moiré” · žiūrėta 2026-11-01

Įstrigai kitur? Klausk — Zorofilm komanda atsako į kiekvieną klausimą.

Užduoti klausimą

Nauji šilkografijos gidai tavo el. pašte

Maždaug vienas el. laiškas per mėnesį: nauji gidai, sprendimai problemoms, apie kurias klausia žmonės, ir Zorofilm naujienos.

Maždaug vienas el. laiškas per mėnesį su naujais šilkografijos gidais ir Zorofilm naujienomis. Pirmiausia el. paštu atsiųsime patvirtinimo nuorodą, o prenumeratos atsisakyti galėsi bet kada. Privatumo politika

Išbandyk su savo maketu

Zorofilm daro tai, ką aiškina šie gidai: spalvų atskyrimą, baltą pagrindą, užlaidą, rastrą ir plėveles, spausdinamas tavo Epson arba eksportuojamas. Free planas leidžia 10 plėvelių per mėnesį, su tiesioginiu spausdinimu.