Skip to content

How to avoid moiré: screen angles for screen printing

Keep the halftone angle away from the mesh threads (0° and 90°) and the 45° pattern of their crossings: 22.5° or 67.5° are the usual choices, and many shops print every spot ink at one angle, such as 22.5° or 25°. No angle is safe on every mesh, so test on your own screens.

3 phút đọc · Cập nhật 2026-11-07 · Zorofilm

What causes moiré on a screen?

Two regular patterns on top of each other make a third, coarser one. A screen has two sources: ink against ink, when halftones of different inks print at angles that beat; and halftone against mesh, because the threads run at 0° and 90° and the knuckles where they cross form a 45° pattern. Rows of dots at 0°, 45° or 90° beat with the mesh.

Which angle should you use?

  • 22.5° or 67.5°, half-way between the threads and the knuckles, is the usual answer; printers on TheShirtBoard report 25° or 61–67° working better on their own screens.
  • Fresener (T-Biz) recommends 20–25° for basic halftones and calls 45°, the offset default, wrong for screen printing.
  • UltraSeps uses 22.5° for CMYK and 26° for everything else.
  • For CMYK, keep the inks 30° apart: Fresener gives 15 / 45 / 75 or 22.5 / 52.5 / 82.5, or one 22.5° or 25° angle for all process colours.

Why one angle for all spot inks?

Opaque inks printed wet on wet at different angles can form rosettes and ink-to-ink moiré. At one angle the mesh question is solved once, and dots of different inks sit side by side. The published settings from UltraSeps and T-Biz, and the Separation Studio manual as quoted on TheShirtBoard, all use one angle per job.

Why can no software predict it exactly?

The mesh is rarely square to the frame and its count changes with tension: a 305 mesh at tension may be about 290 threads per inch, the weft varies by 5–7 %, and a rotated screen changes the frequency (Screen Printing magazine, 2003). Murakami says plainly that “not all angles work”. The honest answer, as one printer on TheShirtBoard puts it, is the angle and dot that work on your screens.

How do you test it?

  1. Print one design with a large flat tint and a gradient at your usual LPI and angle.
  2. Print the same at a second angle, for example 22.5° and 25°.
  3. Print both on the same mesh and compare them on the garment, not on the film: moiré comes from the mesh, so the film alone will not show it.
  4. Keep the angle that looks clean for that mesh and LPI, and write it down per mesh.

What does Zorofilm do?

  • Every job starts at 22.5°; change it in the Halftone tab.
  • An angle within 5° of 0°, 45°, 90° or 135° gets a red warning: it runs along the mesh.
  • An LPI too fine for the mesh gets its own warning; see LPI for mesh count.
  • The loupe shows the real dots of each film at film resolution.

Nguồn

  1. S. Fresener, “All About DPI, LPI, PPI & More”, T-Biz Network, 2015 · truy cập 2026-11-01
  2. S. Roginski, “Suggested Film Output Settings”, UltraSeps (PDF) · truy cập 2026-11-01
  3. S. Fresener, “Simulated Process Color Separations – Part Two”, T-Biz Network, 2018 · truy cập 2026-11-01
  4. TheShirtBoard, “Sim. angles and dpi”, 2014 · truy cập 2026-11-01
  5. Screen Printing magazine, “All Things Are Not as They Appear”, 2003 · truy cập 2026-11-01
  6. Murakami Screen, “How to prevent moiré” · truy cập 2026-11-01

Vướng chuyện khác? Cứ hỏi — đội Zorofilm trả lời mọi câu hỏi.

Đặt câu hỏi

Hướng dẫn in lụa mới, gửi thẳng vào hộp thư của bạn

Khoảng một email mỗi tháng: hướng dẫn mới, cách khắc phục những lỗi mọi người hay hỏi, cùng tin tức từ Zorofilm.

Khoảng một email mỗi tháng với hướng dẫn in lụa mới và tin tức từ Zorofilm. Trước tiên, chúng tôi gửi email cho bạn một liên kết để xác nhận, và bạn có thể hủy đăng ký bất cứ lúc nào. Chính sách quyền riêng tư

Thử trên hình in của chính bạn

Zorofilm làm đúng những gì các hướng dẫn này giải thích: tách màu, lót trắng, trap, tram và phim, in trên máy Epson của bạn hoặc xuất file. Gói Free làm được 10 phim mỗi tháng, đã gồm in trực tiếp.