Skip to content

Trapping for screen printing: how much and which way

Trap by spreading the lighter ink slightly under its darker neighbour, so a small misregistration shows no gap, and never spread onto the garment. A practical size from Screen Printing magazine: print a test, measure the largest gap between the inks, and trap twice that.

3 นาทีในการอ่าน · อัปเดต 2026-11-07 · Zorofilm
สรุปสั้น ๆ
  1. Choose your press in Base & trap
  2. Or measure your press's largest gap and enter twice that
  3. Check the edges between inks with the loupe
  4. Measure again when frames, mesh or press change

Why trap at all?

Screens never register perfectly: frames flex, mesh stretches, platens shift. Where two inks only touch, any shift opens a thin line of garment between them. A trap makes them overlap a little, so a small shift stays hidden under the darker ink.

Which ink spreads?

The lighter one, under the darker one, so the darker edge keeps defining the shape; that is general prepress practice. A black keyline that overprints the colours under it hides registration the same way, and Fresener traps a black outline by fattening the black.

How much trap?

  • Fresener (T-Biz): 2–4 pixels at 300 dpi, about 0.17–0.34 mm, and more on loose presses.
  • Trimingham (Screen Printing, 2025): print a test, measure the largest misregistration gap and trap twice it. His example: a 1/64 in gap gets a 1/32 in trap; specialty items may need 1/16 in or more.
  • Heavy white through fine mesh, and underbase screens, stretch more (Trimingham).
  • Too much trap causes bleeding, loss of detail and colour shifts (Trimingham). Keep a small trap even on a press that registers well.

What does Zorofilm do?

Base & trap → Press sets the trap: Automatic press 0.1 mm, Manual, tight 0.2 mm, Loose / wooden frames 0.4 mm. These are our starting points drawn from the sources above, not measurements of your press, and the app marks them as estimates; type your own value once you have measured your gap. The lighter inks spread under the darkest one inside the artwork only, never onto the shirt. A one-ink job gets no trap.

How do you find your own gap?

This is Trimingham's method: print a two-colour test without trap, using films with marks, find the worst place between the two inks, and measure the gap there (a loupe with a scale helps). Enter twice that as the trap. Your press, frames and mesh decide the number, so measure again when one of them changes.

แหล่งที่มา

  1. S. Fresener, “Choking, Trapping & Cleaning up Type in Photoshop”, T-Biz Network, 2017 · ดึงข้อมูลเมื่อ 2026-11-01
  2. T. Trimingham, “How to trap artwork for screen printing”, Screen Printing, 2025 · ดึงข้อมูลเมื่อ 2026-11-01

ติดเรื่องอื่นอยู่? ถามได้เลย — ทีม Zorofilm ตอบทุกคำถาม

ตั้งคำถาม

คู่มืองานสกรีนใหม่ ส่งตรงถึงอีเมลของคุณ

ประมาณเดือนละหนึ่งอีเมล: คู่มือใหม่ วิธีแก้ปัญหาที่หลายคนถามกันบ่อย และข่าวสารจาก Zorofilm

ประมาณเดือนละหนึ่งอีเมล พร้อมคู่มืองานสกรีนใหม่ และข่าวสารจาก Zorofilm เราจะส่งลิงก์ยืนยันไปทางอีเมลก่อน และคุณยกเลิกการรับข่าวสารได้ทุกเมื่อ นโยบายความเป็นส่วนตัว

ลองกับอาร์ตเวิร์กของคุณเอง

Zorofilm ทำสิ่งที่คู่มือเหล่านี้อธิบาย: การแยกสี underbase, trap, ฮาล์ฟโทน และฟิล์ม พิมพ์บน Epson ของคุณหรือส่งออก แพ็กเกจ Free ทำได้ 10 ฟิล์มต่อเดือน รวมการพิมพ์ตรง