Skip to content

Registration marks and lining up multi-colour films

Put identical registration marks in exactly the same place on every film of a job, check the set on a light table before the screens are made, and let a small trap hide what the press cannot hold. Zorofilm puts four ring-and-cross marks in the same place on every film and numbers the films in print order.

3 분 분량 · 업데이트 2026-11-07 · Zorofilm
요약
  1. Keep the marks on in the Films tab
  2. Measure the 50 mm ruler on the first film
  3. Stack the films on a light table, marks over marks
  4. Check that the whole set is there, in order
  5. Set a trap for what the press cannot hold

What do registration marks do?

They are the same target on every film. Laid on top of each other, the films' marks must coincide; on the press, the screens are adjusted until the printed marks, or the art itself, line up. Shops do it in different ways: printers on TheShirtBoard describe keeping the marks in the same place on every job, and using centre-line marks for one-colour work.

What should every film in a set carry?

  • The same marks in the same position, on films of the same size.
  • The print order (1/4, 2/4…), so nobody burns or prints them out of sequence.
  • The ink, mesh, LPI, angle and dot, so the screen room knows what goes where.
  • A ruler of known length, to prove the film printed at 100 %.
  • Whether it is mirrored.

Zorofilm's films carry all of these: four ring-and-cross targets in the margin, at the middle of each side, and a label strip with job, place, print order, ink, LPI, angle, dot, mesh, resolution, MIRROR when mirrored, the date and a 50 mm ruler. The margin is 15 mm by default; turn the marks off in the Films tab if your press uses its own system.

How do you check a film set?

  1. Measure the 50 mm ruler on one film. If it is not 50 mm, the film was scaled: print it again at 100 %, never “fit to page”.
  2. Stack the films on a light table, marks over marks. They should coincide on every film.
  3. Check that every film of the set is there, in the numbered order.
  4. Look for weak or banded blacks. Banding usually means missing nozzles: Help → Nozzle check prints a small pattern on plain paper.

Which way round does the film go?

Sources disagree on which side of the film should face the screen, so follow your emulsion or film maker's own instructions. If you need the image flipped, turn on Mirror in the Films tab: it flips the art, the marks and the label together, and the label says MIRROR.

And on the press?

Marks get the films right; the press still moves. Trapping hides the small gaps that are left. The registration-mark sheet prints marks for setting up a press without a job.

출처

  1. TheShirtBoard, “Film sizing”, 2017 · 확인 2026-11-04

다른 문제로 막히셨나요? 물어보세요. Zorofilm 팀이 모든 질문에 답합니다.

질문하기

새 실크스크린 인쇄 가이드를 이메일로 받아 보세요

한 달에 이메일 한 통 정도: 새 가이드, 많이들 묻는 문제의 해결법, Zorofilm 소식을 보내 드려요.

새 실크스크린 인쇄 가이드와 Zorofilm 소식을 한 달에 이메일 한 통 정도 보내 드려요. 먼저 확인 링크를 이메일로 보내 드리며, 언제든지 구독을 해지할 수 있어요. 개인정보 처리방침

내 아트워크로 직접 해 보세요

Zorofilm은 이 가이드에서 설명하는 일을 해냅니다: 색분해, 언더베이스, 트래핑, 망점과 필름을 Epson으로 출력하거나 내보냅니다. Free 요금제로 매달 필름 10장, 직접 출력 포함.