Skip to content
무료 · 계정 불필요

이 메쉬에는 어떤 LPI가 맞을까요?

메쉬 수나 LPI를 입력하세요. 공개된 기준마다 결과를 출처와 함께 보여 주고, 그 메쉬가 잡아 줄 것으로 예상되는 최소 망점도 알려 줍니다.

모든 기준을 합치면: 46~66 LPI.

Zorofilm 앱은 메쉬 ÷ 4.5에서 시작합니다: 51 LPI. 내 조합: 메쉬 ÷ LPI = 4.2

공개된 기준별 결과

기준230올/인치의 LPI55 LPI의 메쉬내 조합출처
mesh_tpi = lpi x 4 to 4.5Works only with film output at specific angles ('Not all angles work'); requires four or more mesh openings per halftone dot. S-thread mesh can run 45/55 lpi below the 4x result.51~58 LPI220~248올/인치기준 범위 안Murakami Screen2026-11-01 확인
mesh_tpi = lpi x 3.5 or x 4 (the two most common, treated as minimums)Author calls relying on rules of thumb 'pointless'; nominal counts rounded from metric, weft varies 5-7%, a 305 mesh may be ~290 tpi at tension; a 45° angle lowers effective frequency.58~66 LPI193~220올/인치기준 범위 밖Screen Printing magazine, 'All Things Are Not as They Appear' (April 2003)2026-11-01 확인
lpi = mesh / 5 (or mesh / 4 for a 'dialed-in darkroom')Recommends 22.5° angles; says printers typically choose 30% dot gain.46~58 LPI220~275올/인치기준 범위 안ScreenPrinting.com (Ryonet) blog, 'A Crash Course in Halftones'2026-11-01 확인
mesh = 4-5 x lpi46~58 LPI220~275올/인치기준 범위 안ScreenPrinting.com help centre (Ryonet)2026-11-01 확인
mesh ≈ 4-5 x lpiIts own 305 mesh / 55 lpi pairing (5.5x) falls outside its stated range.46~58 LPI220~275올/인치기준 범위 안Blue Cotton blog2026-11-01 확인
'a mesh that is 4 to 5 times the LPI'Avoid tints above 70%.46~58 LPI220~275올/인치기준 범위 안T-Biz Network (Scott Fresener), 'All About DPI, LPI, PPI & More' (2015-12-10)2026-11-01 확인
>= 3.5:1 required; >= 4.5:1 'international practice'; >= 5:1 for colour halftonesKept as a disagreeing data point.최대 66 LPI193올/인치 이상기준 범위 안ZXC Print (Chinese supplier, low authority)2026-11-01 확인

230올/인치에서 55 LPI의 최소 망점

기준최소 망점출처
Smallest dot/line >= 2 mesh openings + 2 thread diameters, or >= 2 x total screen thickness (mesh + stencil); dots smaller than the opening fall through지름 221 µm ≈ 18% 망점기준으로 계산KIWO-hosted article: Dave Dennings, 'Understanding Mesh Geometry', SGIA Journal, April 19982026-11-01 확인
Printable dot limit: 'Two thread counts and one mesh-opening'Disagrees with D1 (2 openings + 2 threads). Both kept.실 지름을 입력하세요Coates Screen Inks (Harald de Groote), 'Process Printing with UV Inks'2026-11-01 확인
Smallest dot spans two threads + one mesh opening; medium thread diameter preferredSearch snippet only; page behind a bot checkpoint (not bypassed).실 지름을 입력하세요Sefar, 'Half-tone count' FAQ2026-11-01 확인 · 검색 결과 미리보기만 있음. 페이지를 읽을 수 없었습니다
>= 4 mesh open areas per halftone dot지름 249 µm ≈ 23% 망점기준에 대한 저희 해석Murakami Screen2026-11-01 확인
Holding an 8% dot consistently = high quality크기가 아닌 기준점Blue Cotton blog2026-11-01 확인

230올/인치 근처의 공개된 조합

  • 메쉬 240 → 55 LPIWorked example of R1; PDF https://www.murakamiscreen.com/documents/HalftoneAnglestopreventmoire.pdf. Also: white base on 250-300 mesh 'simply won't print well'.Murakami Screen2026-11-01 확인
  • 메쉬 230–265 → 65 LPI65 lpi: 3.5x -> ~230 tpi; 4x -> 255-265 tpi (260)Screen Printing magazine (April 2003)2026-11-01 확인
  • 메쉬 180–225 → 45 LPI180-225 for 45 lpi; suggests 230 'for more margin'ScreenPrinting.com help centre2026-11-01 확인
  • 메쉬 230 → 46–57 LPIScreenPrinting.com help centre2026-11-01 확인
  • 메쉬 205–255 → 45 LPI205 or 255 for 45 lpi ('process minimum')Blue Cotton blog2026-11-01 확인

메쉬 없이: 40-65 lpi 'generally appropriate' for textiles; sweatshirts at least 10 lpi lower; 'Rule of 240': 240 / lpi ≈ viewing distance in feet — Screen Printing magazine (Mark Coudray), Oct 2002, 2026-11-01 확인

경험칙은 서로 다르고, 메쉬의 실제 올 수, 실 굵기, 장력도 제각각입니다. 이 숫자는 출발점일 뿐 망점이 유지된다는 보장이 아닙니다. 최종 판단은 직접 뽑은 테스트 필름으로 하세요.

사용 방법
  1. 메쉬에서 시작할지 LPI에서 시작할지 고르세요.
  2. 숫자를 입력하세요. 올/인치와 올/cm 사이를 전환할 수 있습니다.
  3. 기준별 결과를 읽고 출처를 열어 보세요.
  4. 실 지름이 필요한 최소 망점 기준을 쓰려면 메쉬 실 지름을 입력하세요.
자주 묻는 질문
기준마다 결과가 왜 다른가요?

출처마다 고유한 경험칙을 쓰며, 경험칙은 출발점일 뿐이라고 분명히 말하는 곳도 있습니다. 하나를 고르는 대신 모든 기준을 링크와 함께 보여 줍니다.

올/인치인가요, 올/cm인가요?

1올/cm는 2.54올/인치입니다. 유럽 메쉬는 흔히 cm당 올 수로 표기합니다: 120/cm는 약 305/인치입니다.

최소 망점은 어떻게 계산하나요?

기준의 기하에서 계산합니다: 메쉬 피치(개구부 하나와 실 하나), 망점 셀(1인치 ÷ LPI), 원형 망점. 공개된 기준을 바탕으로 한 저희 계산이며, 망점이 유지된다는 보장은 아닙니다. 최종 판단은 직접 뽑은 테스트 필름으로 하세요.

Zorofilm 앱도 이 기준을 쓰나요?

앱은 시작 LPI로 메쉬 ÷ 4.5를 제안하고, 메쉬 ÷ LPI가 4 아래로, 다시 3.5 아래로 떨어지면 경고합니다.

실제 필름은 앱에서 만드세요

Zorofilm은 아트워크를 색분해하고, 잉크마다 망점을 만들고, 레지스터 마크와 라벨을 넣어 개조 Epson으로 필름을 출력합니다. Free 요금제로 매달 필름 10장을 만들 수 있습니다.