Which LPI for this mesh?
Type a mesh count or an LPI. You get what each published rule says, with its source, and the smallest dot your mesh can be expected to carry.
All the rules together: 46–66 LPI.
The Zorofilm app starts from mesh ÷ 4.5: 51 LPI. Your pair: mesh ÷ LPI = 4.2
What each published rule says
| Rule | LPI for 230 threads/inch | Mesh for 55 LPI | Your pair | Source |
|---|---|---|---|---|
| mesh_tpi = lpi x 4 to 4.5Works only with film output at specific angles ('Not all angles work'); requires four or more mesh openings per halftone dot. S-thread mesh can run 45/55 lpi below the 4x result. | 51–58 LPI | 220–248 threads/inch | within the rule | Murakami Screenretrieved 2026-11-01 |
| mesh_tpi = lpi x 3.5 or x 4 (the two most common, treated as minimums)Author calls relying on rules of thumb 'pointless'; nominal counts rounded from metric, weft varies 5-7%, a 305 mesh may be ~290 tpi at tension; a 45° angle lowers effective frequency. | 58–66 LPI | 193–220 threads/inch | outside the rule | Screen Printing magazine, 'All Things Are Not as They Appear' (April 2003)retrieved 2026-11-01 |
| lpi = mesh / 5 (or mesh / 4 for a 'dialed-in darkroom')Recommends 22.5° angles; says printers typically choose 30% dot gain. | 46–58 LPI | 220–275 threads/inch | within the rule | ScreenPrinting.com (Ryonet) blog, 'A Crash Course in Halftones'retrieved 2026-11-01 |
| mesh = 4-5 x lpi | 46–58 LPI | 220–275 threads/inch | within the rule | ScreenPrinting.com help centre (Ryonet)retrieved 2026-11-01 |
| mesh ≈ 4-5 x lpiIts own 305 mesh / 55 lpi pairing (5.5x) falls outside its stated range. | 46–58 LPI | 220–275 threads/inch | within the rule | Blue Cotton blogretrieved 2026-11-01 |
| 'a mesh that is 4 to 5 times the LPI'Avoid tints above 70%. | 46–58 LPI | 220–275 threads/inch | within the rule | T-Biz Network (Scott Fresener), 'All About DPI, LPI, PPI & More' (2015-12-10)retrieved 2026-11-01 |
| >= 3.5:1 required; >= 4.5:1 'international practice'; >= 5:1 for colour halftonesKept as a disagreeing data point. | up to 66 LPI | 193 threads/inch or finer | within the rule | ZXC Print (Chinese supplier, low authority)retrieved 2026-11-01 |
Smallest dot at 55 LPI on 230 threads/inch
| Rule | Smallest dot | Source |
|---|---|---|
| Smallest dot/line >= 2 mesh openings + 2 thread diameters, or >= 2 x total screen thickness (mesh + stencil); dots smaller than the opening fall through | 221 µm across ≈ 18 % dotcomputed from the rule | KIWO-hosted article: Dave Dennings, 'Understanding Mesh Geometry', SGIA Journal, April 1998retrieved 2026-11-01 |
| Printable dot limit: 'Two thread counts and one mesh-opening'Disagrees with D1 (2 openings + 2 threads). Both kept. | add the thread diameter | Coates Screen Inks (Harald de Groote), 'Process Printing with UV Inks'retrieved 2026-11-01 |
| Smallest dot spans two threads + one mesh opening; medium thread diameter preferredSearch snippet only; page behind a bot checkpoint (not bypassed). | add the thread diameter | Sefar, 'Half-tone count' FAQretrieved 2026-11-01 · search snippet only; the page could not be read |
| >= 4 mesh open areas per halftone dot | 249 µm across ≈ 23 % dotour reading of the rule | Murakami Screenretrieved 2026-11-01 |
| Holding an 8% dot consistently = high quality | a benchmark, not a size | Blue Cotton blogretrieved 2026-11-01 |
Published pairings near 230 threads/inch
- Mesh 240 → 55 LPIWorked example of R1; PDF https://www.murakamiscreen.com/documents/HalftoneAnglestopreventmoire.pdf. Also: white base on 250-300 mesh 'simply won't print well'.Murakami Screenretrieved 2026-11-01
- Mesh 230–265 → 65 LPI65 lpi: 3.5x -> ~230 tpi; 4x -> 255-265 tpi (260)Screen Printing magazine (April 2003)retrieved 2026-11-01
- Mesh 180–225 → 45 LPI180-225 for 45 lpi; suggests 230 'for more margin'ScreenPrinting.com help centreretrieved 2026-11-01
- Mesh 230 → 46–57 LPIScreenPrinting.com help centreretrieved 2026-11-01
- Mesh 205–255 → 45 LPI205 or 255 for 45 lpi ('process minimum')Blue Cotton blogretrieved 2026-11-01
Without a mesh: 40-65 lpi 'generally appropriate' for textiles; sweatshirts at least 10 lpi lower; 'Rule of 240': 240 / lpi ≈ viewing distance in feet — Screen Printing magazine (Mark Coudray), Oct 2002, retrieved 2026-11-01
Rules of thumb disagree, and a mesh's real count, thread and tension vary. These numbers are a starting point, not a promise that a dot will hold: your own test films have the last word.
- Choose whether you start from the mesh or from the LPI.
- Type the number; switch between threads per inch and per cm.
- Read each rule's result and open its source.
- Add your mesh's thread diameter for the smallest-dot rules that need it.
Why do the rules disagree?
Each source uses its own rule of thumb, and some say outright that rules of thumb are only a start. We show every rule with its link instead of picking one.
Threads per inch or per cm?
One thread per cm is 2.54 threads per inch. European mesh is often labelled in threads per cm: 120/cm is about 305 per inch.
How is the smallest dot worked out?
From the rule's geometry: the mesh pitch (one opening plus one thread), the halftone cell (1 inch ÷ LPI) and a round dot. It is our computation from the published rule, not a promise that a dot will hold; your own test films have the last word.
Does the Zorofilm app use these rules?
The app suggests mesh ÷ 4.5 as a starting LPI and warns when mesh ÷ LPI falls under 4, and again under 3.5.
Make the real films in the app
Zorofilm separates your artwork, halftones every ink, adds registration marks and labels, and prints the films on your converted Epson. The Free plan makes 10 films a month.