Skip to content

Which LPI for which mesh count? Rules and a table

Most published rules put the mesh count at 4 to 5 times the LPI: 230 mesh suits about 46–57 LPI (ScreenPrinting.com). Zorofilm suggests mesh ÷ 4.5, warns below ÷ 4 and flags below ÷ 3.5; your own test print has the last word.

3 min read · Updated 2026-11-07 · Zorofilm

What do the sources say?

  • Mesh = 4–5 × LPI: ScreenPrinting.com help centre, Fresener (T-Biz), Blue Cotton.
  • LPI = mesh ÷ 5, or ÷ 4 for a well dialled-in darkroom: ScreenPrinting.com blog.
  • Mesh = LPI × 4 to 4.5, with at least four mesh openings per dot, and only at angles that work: Murakami.
  • × 3.5 and × 4 as minimums, from an author who calls relying on rules of thumb “pointless”: Screen Printing magazine, 2003.
  • At least 3.5 : 1, 4.5 : 1 as “international practice”, 5 : 1 for colour halftones: ZXC Print, a supplier, kept as a disagreeing data point.

They disagree partly because mesh is less regular than its number: nominal counts are rounded from metric, the weft varies by 5–7 %, and a 305 mesh at tension may be about 290 threads per inch (Screen Printing magazine, 2003). The angle matters too; see avoiding moiré.

Mesh to LPI, as published

  • 150 and 180 thin-thread (LX) mesh: 45–55 LPI (Murakami).
  • 160 mesh: 32–40 LPI, ÷ 5 to ÷ 4 (ScreenPrinting.com blog); 35 LPI, “about the lowest most shops use” (Blue Cotton).
  • 180–225 mesh: 45 LPI, with 230 suggested for more margin (ScreenPrinting.com help centre).
  • 200 mesh: 50 LPI (T-Biz).
  • 205–255 mesh: 45 LPI as the process minimum (Blue Cotton).
  • 230 mesh: 46–57 LPI (ScreenPrinting.com help centre).
  • 230–265 mesh: 65 LPI, at 3.5× and 4× (Screen Printing magazine, 2003).
  • 240 mesh: 55 LPI, Murakami's worked example.
  • 305 mesh: 55 LPI (Blue Cotton; 5.5×, outside its own rule).
  • 355 mesh: 85 LPI, KIWO's ExpoCheck example.

The full table with every source and date is on mesh and LPI, and the mesh ↔ LPI calculator does the arithmetic for your mesh.

How fine should textile halftones be?

Screen Printing magazine (Coudray, 2002) calls 40–65 LPI generally appropriate for textiles, at least 10 LPI lower on sweatshirts, and gives a “rule of 240”: 240 ÷ LPI is roughly the viewing distance in feet. Fresener suggests 35–45 LPI for cartoon work, 55 LPI on a manual press and 65 on an automatic.

What is the smallest dot a mesh holds?

  • Two mesh openings plus two thread diameters, or twice the total screen thickness (Dennings, SGIA Journal 1998, hosted by KIWO).
  • Two thread diameters plus one mesh opening (Coates).
  • At least four mesh openings per dot (Murakami).
  • Holding an 8 % dot consistently is high quality (Blue Cotton).

In Zorofilm, Halftone → Smallest dot is From mesh by default: an estimate from two threads plus one opening, using typical thread sizes rather than your mesh's datasheet, and the app marks it as an estimate. Tones below it are dropped and the check strip says so; anything above Solid above (95 % by default) prints solid.

What does Zorofilm check?

  • Under Halftone, the suggestion for your mesh: about mesh ÷ 4.5 LPI, for example 51 LPI on 230 mesh.
  • Amber when mesh ÷ LPI is under 4: small dots may not hold.
  • Red when it is under 3.5: too fine for that mesh.
  • Red when the angle is within 5° of the mesh threads or knuckles (0°, 45°, 90°).

Sources

  1. ScreenPrinting.com help centre, “What mesh count should I use for halftones?” · retrieved 2026-11-01
  2. ScreenPrinting.com blog, “A Crash Course in Halftones” · retrieved 2026-11-01
  3. S. Fresener, “All About DPI, LPI, PPI & More”, T-Biz Network, 2015 · retrieved 2026-11-01
  4. Blue Cotton blog, halftone screen printing · retrieved 2026-11-01
  5. Murakami Screen, “How to prevent moiré” · retrieved 2026-11-01
  6. Murakami Screen, Smart Mesh S + LX · retrieved 2026-11-01
  7. Screen Printing magazine, “All Things Are Not as They Appear”, 2003 · retrieved 2026-11-01
  8. ZXC Print, elimination of moiré patterns (supplier article) · retrieved 2026-11-01
  9. Screen Printing magazine (M. Coudray), October 2002 · retrieved 2026-11-01
  10. D. Dennings, “Understanding Mesh Geometry”, SGIA Journal 1998 (hosted by KIWO, PDF) · retrieved 2026-11-01
  11. Coates Screen Inks (H. de Groote), “Process printing with UV inks” (PDF) · retrieved 2026-11-01
  12. KIWO, ExpoCheck · retrieved 2026-11-01

Stuck on something else? Ask — the Zorofilm team answers every question.

Ask a question

New screen-printing guides in your inbox

About one e-mail a month: new guides, fixes for the problems people ask about, and Zorofilm news.

About one e-mail a month with new screen-printing guides and Zorofilm news. We e-mail you a link to confirm first, and you can unsubscribe anytime. Privacy policy

Try it on your own artwork

Zorofilm does what these guides explain: separations, underbase, trap, halftones and films, printed on your Epson or exported. The Free plan makes 10 films a month, direct printing included.