Skip to content

Choose inkjet film for screen print positives

Buy a waterproof, microporous-coated inkjet film made for screen positives, usually about 5 mil (127 µm) thick, in your printer's sheet or roll size, and judge it by your own density test rather than the box. Published density figures mix UV and visual readings, so they cannot be compared.

3 분 분량 · 업데이트 2026-11-07 · Zorofilm

What should you compare?

  • The coating. Most screen films are sold as waterproof or water-resistant, with a microporous or nanoporous coating that takes a lot of black. Not all: Handprinted's inkjet screen film says it must not get wet, and Prizma's film is water resistant only with pigment inks.
  • Thickness. Most of the films in our table that state one are 5 mil (127 µm) or 130 µm; Epson's Screen Positive Film is 5.3 mil and AWP's 4 mil.
  • Ink. Most say they take both dye and pigment ink; Ulano says the opacity comes from the ink deposit set in the RIP.
  • The coated side. Films are coated on one side; Lawson, for example, says to print on the matte side.
  • Size. Check your printer's sheet or roll width first; the film table lists each product's sheets and rolls.

Can you compare the density on the box?

Not really. Some makers give a UV density, some a visual (optical) one, and some do not say. Prizma's page gives the same film an optical density of 2.6 and a UV density above 4.0. Wasatch, a RIP maker, read the same roll at under 2.0 and over 4.5 depending on the printer's mode, and notes that higher density on inkjet film usually means more dot gain. The number that counts is the one you measure on your printer, ink and film.

What density do trade sources publish?

  • SPTF's capillary film troubleshooting sheet (hosted by KIWO): solid density 3.5 or higher, clear areas 0.3 or less, without saying whether UV or visual.
  • Screen Printing magazine (1999): film Dmax 3.0 or higher, Dmin ideally below 0.1; for inkjet film the UV-stopping ability matters, not visual opacity.
  • Wasatch: a UV Dmax of 2.5 is “high enough for nearly all screen printing”, and 3.0 or more for comfort.

Which films are listed?

The film table lists 18 inkjet films for screen positives, from Lawson, ScreenPrinting.com (Baselayr and Rite), Screen Print Direct, Fixxons, McLogan, Kolormatrix, AWP, Chromaline, Ultrafine, Epson, Ulano, Prizma, PosiPrint, MICRONOM PRO, Printbox, Handprinted and InkStar, each with thickness, coating, ink compatibility, density claim, sizes, a dated price snapshot and its source. Brands we looked for and could not read are listed as not found, not guessed.

How do you test a new film?

Print Zorofilm's density ladder on it, choose the density from that, and keep the film and the setting together: a new film brand means a new test. See film density test.

출처

  1. Handprinted, Inkjet Screen Film · 확인 2026-11-01
  2. Prizma Graphics, Positive Screen Inkjet Film · 확인 2026-11-01
  3. Lawson, Water Resistant Inkjet Film for Film Positives · 확인 2026-11-01
  4. Ulano, Pigment Inkjet Film · 확인 2026-11-01
  5. Epson, Screen Positive Film · 확인 2026-11-01
  6. SPTF, “Capillary Film Troubleshooting” (hosted by KIWO, PDF) · 확인 2026-11-01
  7. F. Basch, “Densitometry: Your Guide to Print Quality”, Screen Printing, 1999 · 확인 2026-11-01
  8. Wasatch SoftRIP help, colour separation linearity · 확인 2026-11-01

다른 문제로 막히셨나요? 물어보세요. Zorofilm 팀이 모든 질문에 답합니다.

질문하기

새 실크스크린 인쇄 가이드를 이메일로 받아 보세요

한 달에 이메일 한 통 정도: 새 가이드, 많이들 묻는 문제의 해결법, Zorofilm 소식을 보내 드려요.

새 실크스크린 인쇄 가이드와 Zorofilm 소식을 한 달에 이메일 한 통 정도 보내 드려요. 먼저 확인 링크를 이메일로 보내 드리며, 언제든지 구독을 해지할 수 있어요. 개인정보 처리방침

내 아트워크로 직접 해 보세요

Zorofilm은 이 가이드에서 설명하는 일을 해냅니다: 색분해, 언더베이스, 트래핑, 망점과 필름을 Epson으로 출력하거나 내보냅니다. Free 요금제로 매달 필름 10장, 직접 출력 포함.