Skip to content

Trapping for screen printing: how much and which way

Trap by spreading the lighter ink slightly under its darker neighbour, so a small misregistration shows no gap, and never spread onto the garment. A practical size from Screen Printing magazine: print a test, measure the largest gap between the inks, and trap twice that.

3 min čítania · Aktualizované 2026-11-07 · Zorofilm
V skratke
  1. Choose your press in Base & trap
  2. Or measure your press's largest gap and enter twice that
  3. Check the edges between inks with the loupe
  4. Measure again when frames, mesh or press change

Why trap at all?

Screens never register perfectly: frames flex, mesh stretches, platens shift. Where two inks only touch, any shift opens a thin line of garment between them. A trap makes them overlap a little, so a small shift stays hidden under the darker ink.

Which ink spreads?

The lighter one, under the darker one, so the darker edge keeps defining the shape; that is general prepress practice. A black keyline that overprints the colours under it hides registration the same way, and Fresener traps a black outline by fattening the black.

How much trap?

  • Fresener (T-Biz): 2–4 pixels at 300 dpi, about 0.17–0.34 mm, and more on loose presses.
  • Trimingham (Screen Printing, 2025): print a test, measure the largest misregistration gap and trap twice it. His example: a 1/64 in gap gets a 1/32 in trap; specialty items may need 1/16 in or more.
  • Heavy white through fine mesh, and underbase screens, stretch more (Trimingham).
  • Too much trap causes bleeding, loss of detail and colour shifts (Trimingham). Keep a small trap even on a press that registers well.

What does Zorofilm do?

Base & trap → Press sets the trap: Automatic press 0.1 mm, Manual, tight 0.2 mm, Loose / wooden frames 0.4 mm. These are our starting points drawn from the sources above, not measurements of your press, and the app marks them as estimates; type your own value once you have measured your gap. The lighter inks spread under the darkest one inside the artwork only, never onto the shirt. A one-ink job gets no trap.

How do you find your own gap?

This is Trimingham's method: print a two-colour test without trap, using films with marks, find the worst place between the two inks, and measure the gap there (a loupe with a scale helps). Enter twice that as the trap. Your press, frames and mesh decide the number, so measure again when one of them changes.

Zdroje

  1. S. Fresener, “Choking, Trapping & Cleaning up Type in Photoshop”, T-Biz Network, 2017 · získané 2026-11-01
  2. T. Trimingham, “How to trap artwork for screen printing”, Screen Printing, 2025 · získané 2026-11-01

Zasekol si sa na niečom inom? Opýtaj sa — tím Zorofilm odpovedá na každú otázku.

Opýtať sa

Nové návody na sieťotlač priamo do tvojej schránky

Zhruba jeden e-mail mesačne: nové návody, riešenia problémov, na ktoré sa ľudia pýtajú, a novinky zo Zorofilmu.

Zhruba jeden e-mail mesačne s novými návodmi na sieťotlač a novinkami zo Zorofilmu. Najprv ti e-mailom pošleme odkaz na potvrdenie a z odberu sa môžeš kedykoľvek odhlásiť. Zásady ochrany súkromia

Vyskúšaj to na vlastnej grafike

Zorofilm robí to, čo tieto návody vysvetľujú: separácie, biely podklad, presahy, raster a filmy, tlačené na tvojom Epsone alebo exportované. Plán Free urobí 10 filmov mesačne, vrátane priamej tlače.