Skip to content

Trapping for screen printing: how much and which way

Trap by spreading the lighter ink slightly under its darker neighbour, so a small misregistration shows no gap, and never spread onto the garment. A practical size from Screen Printing magazine: print a test, measure the largest gap between the inks, and trap twice that.

3 分で読めます · 更新 2026-11-07 · Zorofilm
要点
  1. Choose your press in Base & trap
  2. Or measure your press's largest gap and enter twice that
  3. Check the edges between inks with the loupe
  4. Measure again when frames, mesh or press change

Why trap at all?

Screens never register perfectly: frames flex, mesh stretches, platens shift. Where two inks only touch, any shift opens a thin line of garment between them. A trap makes them overlap a little, so a small shift stays hidden under the darker ink.

Which ink spreads?

The lighter one, under the darker one, so the darker edge keeps defining the shape; that is general prepress practice. A black keyline that overprints the colours under it hides registration the same way, and Fresener traps a black outline by fattening the black.

How much trap?

  • Fresener (T-Biz): 2–4 pixels at 300 dpi, about 0.17–0.34 mm, and more on loose presses.
  • Trimingham (Screen Printing, 2025): print a test, measure the largest misregistration gap and trap twice it. His example: a 1/64 in gap gets a 1/32 in trap; specialty items may need 1/16 in or more.
  • Heavy white through fine mesh, and underbase screens, stretch more (Trimingham).
  • Too much trap causes bleeding, loss of detail and colour shifts (Trimingham). Keep a small trap even on a press that registers well.

What does Zorofilm do?

Base & trap → Press sets the trap: Automatic press 0.1 mm, Manual, tight 0.2 mm, Loose / wooden frames 0.4 mm. These are our starting points drawn from the sources above, not measurements of your press, and the app marks them as estimates; type your own value once you have measured your gap. The lighter inks spread under the darkest one inside the artwork only, never onto the shirt. A one-ink job gets no trap.

How do you find your own gap?

This is Trimingham's method: print a two-colour test without trap, using films with marks, find the worst place between the two inks, and measure the gap there (a loupe with a scale helps). Enter twice that as the trap. Your press, frames and mesh decide the number, so measure again when one of them changes.

出典

  1. S. Fresener, “Choking, Trapping & Cleaning up Type in Photoshop”, T-Biz Network, 2017 · 取得 2026-11-01
  2. T. Trimingham, “How to trap artwork for screen printing”, Screen Printing, 2025 · 取得 2026-11-01

ほかに困っていることはありますか?質問してください。Zorofilmチームがすべての質問に回答します。

質問する

新しいスクリーン印刷ガイドをメールでお届け

月1通ほどのメールで、新しいガイド、よく寄せられるトラブルの解決策、Zorofilmのお知らせをお届けします。

新しいスクリーン印刷ガイドとZorofilmのお知らせを月1通ほどお届けします。まず確認用のリンクをメールでお送りします。配信はいつでも停止できます。 プライバシーポリシー

ご自身のアートワークで試してみましょう

Zorofilmは、これらのガイドで説明していることを実行します:色分解、白下地、トラッピング、網点、フィルムを、Epsonで出力または書き出し。Freeプランは毎月10枚、直接出力も含みます。