- Ask for a vector PDF or AI with spot colours, or a PSD with spot channels
- Otherwise a transparent PNG at about 300 ppi at print size
- Outline or embed the fonts
- Remove background boxes
- Check thin lines against the mesh you will use
Which file should you ask the customer for?
- Best: a vector PDF or Illustrator AI file, with the spot colours named the way the inks should be. It stays sharp at any size and its spot colours become the inks. AI files need “Create PDF Compatible File” on; see PDF and AI spot colours.
- Good: a PSD already separated into spot channels, one per ink. See PSD with spot channels.
- Fine: a PNG with a transparent background at about 300 ppi at print size. One print shop's published requirements ask for 300 dpi at print size, no more than about 10 % scaling, and outlined fonts (FSG Prints).
- Last resort: a JPEG. Compression leaves speckles around edges; Zorofilm cleans them up, but a PNG, PDF or AI of the same design separates better.
- Not read: EPS, legacy Illustrator files and AI files saved without PDF content. Zorofilm says what to export instead, usually a PDF.
How much resolution is enough?
Work it out at the print size, not from the pixel count. A 3,000 pixel wide file printed 254 mm (10 in) wide is 300 ppi; the same file across a 381 mm (15 in) back is 200 ppi. At 72 ppi one pixel is 0.35 mm wide, so edges step and small text blurs. Zorofilm shows the effective ppi at the width you set and warns when it is low. A file that does not state a print size is assumed to be 300 ppi until you set the width.
What about fonts?
Convert the type to outlines, or embed the fonts, before the PDF is saved. A font that is neither gets replaced by another one when the file is opened on a different computer, and the film shows the substitute.
What makes a design hard to separate?
- A solid background box. On a dark shirt it would print as a rectangle. Turn on Remove the background in the Job tab, or set the garment to that colour.
- A photo of the design, on paper, a screen or a shirt. Phone photos rarely separate cleanly: ask for the original file.
- Photos and painted art. Spot inks posterise them; simulated process, the method for photos, is planned for Zorofilm and is not in this version. Spot, index and simulated process explains the difference.
- More colours than the press has heads. Past six inks Zorofilm asks you to check that your press has enough heads, and it points out inks so close that merging them saves a screen.
- Lines and dots thinner than the screen holds. Published rules put the smallest printable dot at two thread diameters plus one mesh opening (Coates) or two openings plus two threads (Dennings, hosted by KIWO): the coarser the mesh, the bolder the detail has to be. Zorofilm also warns when the underbase choke would take the base away from thin lines.
How big should the print be?
That is your call and the customer's; set the width in the Job tab. Zorofilm offers starting widths for common places (left chest, full front, full back, youth front, sleeve, oversize), and can add the same design at another place or size as a second job with the same inks, its films labelled with the place.
Viri
- FSG Prints, art requirements · pridobljeno 2026-11-04
- Coates Screen Inks (H. de Groote), “Process printing with UV inks” (PDF) · pridobljeno 2026-11-01
- D. Dennings, “Understanding Mesh Geometry”, SGIA Journal 1998 (hosted by KIWO, PDF) · pridobljeno 2026-11-01
Ti nagaja kaj drugega? Vprašaj — ekipa Zorofilm odgovori na vsako vprašanje.
Postavi vprašanjeNovi vodniki za sitotisk neposredno v tvoj nabiralnik
Približno eno e-sporočilo na mesec: novi vodniki, rešitve za težave, o katerih ljudje sprašujejo, in novice Zorofilm.
